800.839.9018neil@nadcoinc.com
NADCO® Smooth Cling Films utilize a unique acrylic adhesive system that allows the adhesive to flow on to a surface with little to no application pressure. The self wetting adhesive is nearly ultra-clear which provides excellent transparency. These protective label stocks are ideal for use in many industrial and commercial applications. Some typical applications include: printed window advertisements and protecting mobile handheld displays during shipment from the manufacturer to end user, printed clear labels, protective over laminates, and surface protection.
Unit of Measure

Specifications

Printing Film Type

N/A Polyester

Room Temperature Storage Conditions

N/A 72 ºF22 ºC

Construction

Thickness (Facestock)

N/A 5 mil0.127 mm

Material (Facestock )

N/A Clear Polyethylene Terephthalate (PET)

Thickness (Adhesive)

N/A 1 mil

Type (Adhesive)

N/A 1200 Adhesive (Low Adhesion)

Thickness (Release Liner)

N/A 2 mil0.5 mm

Note for Construction

N/A The caliper listed is based on a calculation from manufacturing controlled adhesive coat weights using a density of 1.012 g/cc.

Typical Physical Properties

90 Degree (º) Peel Adhesion at 20 Minute (min) Dwell Time for Stainless Steel Material (12 Inch/Minute (in./min.) (305 Millimeter/Minute (mm/min))

N/A 25 g/in

90 Degree (º) Peel Adhesion at 20 Minute (min) Dwell Time for Glass Material (12 Inch/Minute (in./min.) (305 Millimeter/Minute (mm/min))

N/A 25 g/in

90 Degree (º) Peel Adhesion at 20 Minute (min) Dwell Time for Polycarbonate Material (12 Inch/Minute (in./min.) (305 Millimeter/Minute (mm/min))

N/A 25 g/in

Release Liner

Release Liner

N/A 25 g/in

Test Method for Optics (without Liner)

N/A ASTM D1003

Typical Haze

N/A <2 %

Relative Humidity

N/A 50 %

Enviromental Aging Test

Environmental Aging Tests

N/A Environmental Aging to glass. Tests carried out at conditions noted below. After test samples left at standard conditions for 2 hours, then evaluated. Standard conditions are 23 ºC and 50 % relative humidity.

Environmental Aging Tests for 16 Hours (hr) at -40 Degree Celsius (ºC) Temperature

N/A 10 g/in

Environmental Aging Tests for 16 Hours (hr) at 185 Degree Celsius (ºC) Temperature

N/A 40 g/in

Temperature Cycling

N/A 10 g/in

Environmental Aging Tests for

N/A 5 g/in

Standard Time for Environmental Aging Tests

N/A 2 h

Standard Temperature for Environmental Aging Tests

N/A 23 ºC

Standard Relative Humidity for Environmental Aging Tests

N/A 50 %

Adhesive

Peel Adhesion Angle

N/A 90 º

Dwell Time for Peel Adhesion

N/A 20 min

Material for Peel Adhesion

N/A Stainless Steel Glass Polycarbonate

Features

Features

N/A
  • Ultra-clear, high transparency film and adhesive combination-suitable for display panels.
  • Removable adhesive-easily removable from many surfaces with no adhesive residue.
  • PET linered product allows for die-cutting to any shape and is suitable for high-speed, automatic dispensing.
  • PET face material-much higher temperature resistance than PE protective Films.
  • Before application the surfaces must be free from oil, fat, dust and solvents. Best results are achieved when applied between 50°F and 104°F.
  • The product has a high transparency (low haze).
  • The adhesive is cleanable with water so it may be re-used.

Applications

Application Ideas

N/A
  • Protect window apertures and displays in electronics applications.
  • Temporary protection of sensitive surfaces against dirt, dust and damage during processing, storage and mounting etc.
  • Low level of adhesion and is suitable for protection of many surfaces including: Glass, Varnished/hard coated surfaces, aluminum and plastic surfaces.
  • Printed window film and advertisements

Printing

Printing

N/A The polyester film is designed with a printable surface suitable for printing instructions, promotional messages or bar codes via thermal transfer and conventional flexographic printing methods.

Storage

Storage

N/A Store at room temperature conditions of 72 ºF (22 ºC) and 50 % relative humidity.

Shelf Life

Shelf Life

N/A If stored under proper conditions, product retains its performance and properties for one year from date of manufacture.

Technical Information

Technical Information

N/A The technical information, recommendations and other statements contained in this document are based upon tests or experience that NADCO® believes are reliable, but the accuracy or completeness of such information is not guaranteed.

Product Use

Product Use

N/A Many factors beyond NADCO® control and uniquely within user's knowledge and control can affect the use and performance of a NADCO® product in a particular application. Given the variety of factors that can affect the use and performance of a NADCO® product, user is solely responsible for evaluating the NADCO® product and determining whether it is fit for a particular purpose and suitable for user's method of application.

Warranty, Limited Remedy, and Disclaimer

Warranty, Limited Remedy, and Disclaimer

N/A Unless an additional warranty is specifically stated on the applicable NADCO® product packaging or product literature, NADCO® warrants that each NADCO® product meets the applicable NADCO® product specification at the time NADCO® ships the product. NADCO® makes no other warranties or conditions, express or implied, including, but not limited to, any implied warranty or condition of merchantability or fitness for a particular purpose or any implied warranty or condition arising out of a course of dealing, custom or usage of trade. If the NADCO® product does not conform to this warranty, then the sole and exclusive remedy is, at NADCO® option, replacement of the NADCO® product or refund of the purchase price.

Limitation of Liability

Limitation of Liability

N/A Except where prohibited by law, NADCO® will not be liable for any loss or damage arising from the NADCO® product, whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted, including warranty, contract, negligence or strict liability.

Note

Note

N/A Technical information and data should be considered representative or typical only and should not be used for specification purposes.
^